Gemalto is now part of the Thales Group, find out more.

You are here

RAS connection on Windows 7 with ELS61T on serial port com | Thales IoT Developer Community

September 12, 2017 - 12:15pm, 1577 views

Hi,

I want to set an internet connection on windows 7 using ****m ELS61T on serial port.

I have previously made this kind of connection with EHS6T, but with usb and it works.

On the ELS61T, I have no usb port. So I try to set the connection on port com.

First, In control panel-> ****m I had a new ****m on port com using the ELS61T driver (ehxmdms.inf) on port com1.

The ****m is correctly create in windows, in his propeties I can check the connection with the ****m.

In advanced parameter, I had at+cgdcont=1,"ip","a2bouygtel.com"

Then in network-> new remote connection, I set the phone number to *99***1#. The connection is created.

But when I try to open the connection, I have two kind of error, error 651 or error 692.

Of course pin code is ok, and I have this config :

^SCFG: "Gpio/****/ASC1","std"
^SCFG: "Gpio/****/DCD0","gpio"
^SCFG: "Gpio/****/DSR0","rsv"
^SCFG: "Gpio/****/DTR0","gpio"
^SCFG: "Gpio/****/FSR","gpio"
^SCFG: "Gpio/****/PULSE","gpio"
^SCFG: "Gpio/****/PWM","gpio"
^SCFG: "Gpio/****/RING0","gpio"
^SCFG: "Gpio/****/SPI","rsv"
^SCFG: "Gpio/****/SYNC","std"
^SCFG: "GPRS/AutoAttach","enabled"
^SCFG: "Ident/Manufacturer","Cinterion"
^SCFG: "Ident/Product","ELS61-E"
^SCFG: "MEopMode/SoR","off"
^SCFG: "MEopMode/CregRoam","0"
^SCFG: "MeOpMode/SRPOM","0"
^SCFG: "MEShutdown/Fso","0"
^SCFG: "MEShutdown/sVsup/threshold","0","0"
^SCFG: "Radio/Band/2G","0x00000014"
^SCFG: "Radio/Band/4G","0x08080085"
^SCFG: "Radio/Mtpl/2G","0"
^SCFG: "Radio/Mtpl/4G","0"
^SCFG: "Radio/OutputPowerReduction","4"
^SCFG: "Serial/Interface/Allocation","1","1"
^SCFG: "Serial/USB/DDD","0","0","0409","1E2D","005B","Cinterion Wireless Modules","ELSx",""
^SCFG: "Tcp/IRT","3"
^SCFG: "Tcp/MR","10"
^SCFG: "Tcp/OT","6000"
^SCFG: "Tcp/WithURCs","on"
^SCFG: "Trace/Syslog/OTAP","0"
^SCFG: "Userware/Autostart","0"
^SCFG: "Userware/Autostart/Delay","10"
^SCFG: "Userware/DebugInterface","0.0.0.0","0.0.0.0","0"
^SCFG: "Userware/DebugMode","off"
^SCFG: "Userware/Passwd",
^SCFG: "Userware/Stdout","null",,,,"off"
^SCFG: "Userware/Watchdog","1"

I think it's a problem in windows, do you know this case ?

I tried to use EHS6T on port com, I have the same problem.

Thanks.