PLS8-EU modem always starts in airplane mode | Telit Cinterion IoT Developer Community
March 16, 2023 - 7:01pm, 200 views
Hello, I currently have a Cinterion PLS8-UE R4 modem connected to a linux operating system. Every time the computer restarts, it always starts in airplane mode. I must execute the AT+CFUN=1 command so that it exits airplane mode, when consulting with the command AT^SCFG? It shows me the following information:
Cinterion
PLS8-US R4
REVISION 04.004
^SCFG: "Audio/Ecfg","0"
^SCFG: "Audio/Loop","0"
^SCFG: "Audio/SvTone","0"
^SCFG: "Call/ECC","0"
^SCFG: "Call/Speech/Codec","0"
^SCFG: "Call/VoLTE/Codec","0"
^SCFG: "GPIO/Mode/Antenna","off"
^SCFG: "GPRS/Auth","2"
^SCFG: "GPRS/AutoAttach","enabled"
^SCFG: "MEopMode/CFUN","1","1"
^SCFG: "MEopMode/DTM/Mode","1"
^SCFG: "MEopMode/ExpectDTR","current","acm1","acm2","acm3","acm4","rmnet0","rmn"
^SCFG: "MEopMode/ExpectDTR","powerup","acm1","acm2","acm3","acm4","rmnet0","rmn"
^SCFG: "MEopMode/IMS","1","mmtel","smsip"
^SCFG: "MEopMode/NonBlock/Cops","0"
^SCFG: "MEopMode/PingRsp","1"
^SCFG: "MEopMode/PowerMgmt/LCI","disabled"
^SCFG: "MEopMode/Prov/AutoSelect","on"
^SCFG: "MEopMode/Prov/Cfg","fallbvcus*"
^SCFG: "MEopMode/PwrSave","disabled","52","50"
^SCFG: "MEopMode/SRPOM","0"
^SCFG: "MEShutdown/OnIgnition","off"
^SCFG: "MEShutdown/Timer","off"
^SCFG: "Misc/CId",""
^SCFG: "Radio/Band","1262191"
^SCFG: "Radio/CNS","0"
^SCFG: "Radio/Mtpl","0"
^SCFG: "Radio/OutputPowerReduction","4"
^SCFG: "RemoteWakeUp/Event/ASC","none"
^SCFG: "RemoteWakeUp/Event/URC","none"
^SCFG: "RemoteWakeUp/Event/USB","none"
^SCFG: "RemoteWakeUp/Ports","current","acm1","acm2","acm3","acm4","rmnet0","rmn"
^SCFG: "RemoteWakeUp/Ports","powerup","acm1","acm2","acm3","acm4","rmnet0","rmn"
^SCFG: "RemoteWakeUp/Pulse","10"
^SCFG: "SIM/CS","SIM_1"
^SCFG: "SIM/Retry","on"
^SCFG: "SMS/4GPref","IMS"
^SCFG: "SMS/AutoAck","0"
^SCFG: "SMS/Retrm",45
^SCFG: "Tcp/IPv6Priv","1"
^SCFG: "Tcp/Loop","disabled"
^SCFG: "Tcp/MR","10"
^SCFG: "Tcp/OT","6000"
^SCFG: "Tcp/TLS/Version","MIN","***"
^SCFG: "Tcp/UnreachRsp","1"
^SCFG: "Tcp/WithURCs","on"
^SCFG: "URC/DstIfc","app"
^SCFG: "URC/Ringline","local"
^SCFG: "URC/Ringline/ActiveTime","2"
^SCFG: "URC/Ringline/SelWUrc","all"
because I always have to execute this command so that the modem starts correctly. what setting should i change
Regards.
Hello,
According to SCFG "GPRS/AutoAttach" it should start with CFUN 1. Is it CFUN 4 or something else? How do you restart the module?
You may also try to change the first parameter to 0, set CFUN=1 and then check what happens after reboot.
BR,
Bartłomiej