JRC File version | Telit Cinterion IoT Developer Community
January 21, 2020 - 3:33pm, 1973 views
Hello, I have problem with AT^SSPI, It's still reply ERROR. I think It may be JRC file version not proper version.
[TX] - AT^SSPI=0000,0000,0000<CR>
1/21/2020 21:16:26.394 [RX] - AT^SSPI=0000,0000,0000<CR>
<CR><LF>
ERROR<CR><LF>
1/21/2020 21:23:58.429 [TX] - ATI1<CR>
1/21/2020 21:23:58.431 [RX] - ATI1<CR>
<CR><LF>
Cinterion<CR><LF>
EHS6<CR><LF>
REVISION 02.000<CR><LF>
A-REVISION 00.000.19<CR><LF>
<CR><LF>
OK<CR><LF>
Cloud you help this issue please ?
Thank you
Hello,
Please check AT^SCFG? output if autostart is active:
^SCFG: "Userware/Autostart","1"
and if SPI interface is active:
^SCFG: "Gpio/mode/SPI","std"
Please also send AT+CMEE=2 before you try SSPI command again.
As for JRC version please check it with AT^SJAM=4 command. It must be correct if you haven't updated the firmware or JRC.
Regards,
Bartłomiej
I try check it.
1/23/2020 09:58:02.271 [TX] - AT^SCFG?<CR>
1/23/2020 09:58:02.277 [RX] - AT^SCFG?<CR>
<CR><LF>
^SCFG: "Audio/Loop","0"<CR><LF>
^SCFG: "Call/Ecall/AckTimeout","5000"<CR><LF>
^SCFG: "Call/Ecall/Callback","0"<CR><LF>
^SCFG: "Call/Ecall/CallbackTimeout","43200000"<CR><LF>
^SCFG: "Call/Ecall/Msd","0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000"<CR><LF>
^SCFG: "Call/Ecall/Pullmode","0"<CR><LF>
^SCFG: "Call/Ecall/SessionTimeout","20000"<CR><LF>
^SCFG: "Call/Ecall/StartTimeout","5000"<CR><LF>
^SCFG: "Call/ECC","0"<CR><LF>
^SCFG: "Call/Speech/Codec","0"<CR><LF>
^SCFG: "Gpio/mode/ASC1","std"<CR><LF>
^SCFG: "Gpio/mode/DAI","gpio"<CR><LF>
^SCFG: "Gpio/mode/DCD0","gpio"<CR><LF>
^SCFG: "Gpio/mode/DSR0","gpio"<CR><LF>
^SCFG: "Gpio/mode/DTR0","gpio"<CR><LF>
^SCFG: "Gpio/mode/FSR","gpio"<CR><LF>
^SCFG: "Gpio/mode/HSIC","rsv"<CR><LF>
^SCFG: "Gpio/mode/PULSE","gpio"<CR><LF>
^SCFG: "Gpio/mode/PWM","gpio"<CR><LF>
^SCFG: "Gpio/mode/RING0","gpio"<CR><LF>
^SCFG: "Gpio/mode/SPI","rsv"<CR><LF>
^SCFG: "Gpio/mode/SYNC","gpio"<CR><LF>
^SCFG: "GPRS/AutoAttach","enabled"<CR><LF>
^SCFG: "Ident/Manufacturer","Cinterion"<CR><LF>
^SCFG: "Ident/Product","EHS6"<CR><LF>
^SCFG: "MEopMode/Dormancy","0","0"<CR><LF>
^SCFG: "MEopMode/SoR","off"<CR><LF>
^SCFG: "MEShutdown/Fso","0"<CR><LF>
^SCFG: "MEShutdown/sVsup/threshold","0","0"<CR><LF>
^SCFG: "Radio/Band","511"<CR><LF>
^SCFG: "Radio/OutputPowerReduction","4"<CR><LF>
^SCFG: "Serial/Interface/Allocation","1","1"<CR><LF>
^SCFG: "Serial/USB/DDD","0","0","0409","1E2D","0058","Cinterion Wireless Modules","EHx",""<CR><LF>
^SCFG: "Tcp/IRT","3"<CR><LF>
^SCFG: "Tcp/MR","10"<CR><LF>
^SCFG: "Tcp/OT","6000"<CR><LF>
^SCFG: "Tcp/WithURCs","on"<CR><LF>
^SCFG: "Trace/Syslog/OTAP","0"<CR><LF>
^SCFG: "Userware/Autostart","1"<CR><LF>
^SCFG: "Userware/Autostart/Delay","0"<CR><LF>
^SCFG: "Userware/DebugInterface","0.0.0.0","0.0.0.0","0"<CR><LF>
^SCFG: "Userware/DebugMode","off"<CR><LF>
^SCFG: "Userware/Passwd",<CR><LF>
^SCFG: "Userware/Stdout","usb3",,,,"off"<CR><LF>
^SCFG: "Userware/Watchdog","1"<CR><LF>
<CR><LF>
OK<CR><LF>
1/23/2020 09:58:34.050 [TX] - AT^SJAM=4<CR>
1/23/2020 09:58:34.095 [RX] - AT^SJAM=4<CR>
<CR><LF>
^SJAM: "a:/app.jad","APP","ASDF","1.26.74",1,545580,0<CR><LF>
<CR><LF>
OK<CR><LF>
1/23/2020 09:58:36.045 [TX] - AT^SJAM=5<CR>
1/23/2020 09:58:36.148 [RX] - AT^SJAM=5<CR>
<CR><LF>
^SJAM: "a:/app.jad","APP","ASDF","1.26.74",1<CR><LF>
<CR><LF>
OK<CR><LF>
1/23/2020 09:59:02.174 [TX] - AT+CMEE=2<CR>
1/23/2020 09:59:02.176 [RX] - AT+CMEE=2<CR>
<CR><LF>
OK<CR><LF>
1/23/2020 09:59:22.453 [TX] - AT^SSPI=0000,0000,0000<CR>
1/23/2020 09:59:22.455 [RX] - AT^SSPI=0000,0000,0000<CR>
<CR><LF>
+CME ERROR: Unknown<CR><LF>
it look like it does not have jrc file, please suggest how to set I2C or SPI active completly.
Thank you so much
Hello,
You need to enable SPI interface by setting:
AT^SCFG="Gpio/mode/SPI","std"
and reboot the module.
As for JRC it seems that it is not installed. I'll send you an info how you can install it by email.
Regards,
Bartłomiej
Thank you so much, I'm testing now.
cloud you send me for this verion below too ?
ATI1<CR>
<CR><LF>
Cinterion<CR><LF>
EHS6<CR><LF>
REVISION 03.001<CR><LF>
A-REVISION 00.000.31<CR><LF>
<CR><LF>
OK<CR><LF>
Advance thank you so much.
You should have got it already.
Regards,
Bartłomiej