EHSX USF UPLOAD | Telit Cinterion IoT Developer Community
June 12, 2018 - 4:45pm, 2071 views
I have tryed to run
ehs6_gwinswup_rev02.000_arn0000015.exe
But the result is ->
ERROR: Module not applicable for swup process!
June 12, 2018 - 4:45pm, 2071 views
I have tryed to run
ehs6_gwinswup_rev02.000_arn0000015.exe
But the result is ->
ERROR: Module not applicable for swup process!
I have some EHS6 and EHS8 and ELS61
Is it possible to get an gwin-usf for all the modules?
br
Hello,
For EHS6 and EHS8 you may load the same firmware and for ELS61 you need other firmware.
Please check the detailed firmware version that is installed on each module with ATI1 command.
Regards,
Bartłomiej
Dear sir, I have attched a dump from my app EHS.
For some reasom I can not send any SMS.
Some help is needed. Br
Sorry, forgot the cfg-dump:
AT^SCFG?
^SCFG: "Audio/Loop","0"
^SCFG: "Call/ECC","0"
^SCFG: "Call/Ecall/AckTimeout","5000"
^SCFG: "Call/Ecall/Callback","0"
^SCFG: "Call/Ecall/CallbackTimeout","43200000"
^SCFG: "Call/Ecall/Msd","etc000
^SCFG: "Call/Ecall/Pullmode","0"
^SCFG: "Call/Ecall/SessionTimeout","20000"
^SCFG: "Call/Ecall/StartTimeout","5000"
^SCFG: "Call/Speech/Codec","0"
^SCFG: "GPRS/AutoAttach","enabled"
^SCFG: "Gpio/mode/ASC1","std"
^SCFG: "Gpio/mode/DAI","gpio"
^SCFG: "Gpio/mode/DCD0","std"
^SCFG: "Gpio/mode/DSR0","std"
^SCFG: "Gpio/mode/DTR0","std"
^SCFG: "Gpio/mode/FSR","gpio"
^SCFG: "Gpio/mode/HSIC","rsv"
^SCFG: "Gpio/mode/PULSE","gpio"
^SCFG: "Gpio/mode/PWM","gpio"
^SCFG: "Gpio/mode/RING0","gpio"
^SCFG: "Gpio/mode/SPI","rsv"
^SCFG: "Gpio/mode/SYNC","gpio"
^SCFG: "Ident/Manufacturer","Cinterion"
^SCFG: "Ident/Product","EHS6"
^SCFG: "MEShutdown/Fso","0"
^SCFG: "MEShutdown/sVsup/threshold","0","0"
^SCFG: "MEopMode/CFUN","0","1"
^SCFG: "MEopMode/Dormancy","0","0"
^SCFG: "MEopMode/SoR","off"
^SCFG: "Radio/Band","511"
^SCFG: "Radio/Mtpl","0"
^SCFG: "Radio/OutputPowerReduction","4"
^SCFG: "Serial/Interface/Allocation","1","1"
^SCFG: "Serial/USB/DDD","0","0","0409","1E2D","0058","Cinterion Wireless Modules","EHx",""
^SCFG: "Tcp/IRT","3"
^SCFG: "Tcp/MR","10"
^SCFG: "Tcp/OT","6000"
^SCFG: "Tcp/WithURCs","on"
^SCFG: "Trace/Syslog/OTAP","0"
^SCFG: "URC/Ringline","local"
^SCFG: "URC/Ringline/ActiveTime","2"
^SCFG: "Userware/Autostart","1"
^SCFG: "Userware/Autostart/Delay","0"
^SCFG: "Userware/DebugInterface","0.0.0.0","0.0.0.0","0"
^SCFG: "Userware/DebugMode","off"
^SCFG: "Userware/Passwd",
^SCFG: "Userware/Stdout","asc1",,,,"off"
^SCFG: "Userware/Watchdog","0"
OK
Hi,
Please use AT+CMGS="123456" and it should work.
Best regards,
Antero Markkula
Antero Markkula
Communication and Mechatronics
Enkom Active Oy – www.enkom-active.fi
Upseerinkatu 3 A, 02600 Espoo, Finland
Mobile: +358 400 411368
Office: +358 10 204 0000
Fax: +358 10 204 0010
E-mail: antero.markkula@enkom-active.fi
Sorry Markkula.
Thanks, of course