Thales' cellular IoT products business is now part of Telit Cinterion, find out more.

You are here

EHS8 ARN 00.000.51 serial communication not working | Telit Cinterion IoT Developer Community

July 21, 2017 - 12:24pm, 2770 views

Dear,

We’ve upgraded an EHS8 from A-REVISION 00.000.14 to 00.000.51. Now we can’t get the serial communication working on ASC1 though it works fine on the old revision.

We’ve set the following parameters:

  • Disabled power saving: AT^SPOW=1,0,0
  • ASC1 for serial communication: AT^SCFG="Serial/Interface/Allocation","1"
  • ASC1 as output: AT^SCFG="Gpio/mode/ASC1","std"

Below is a snapshot of the Extended Configuration Settings:

at^scfg?

^SCFG: "Audio/Loop","0"

^SCFG: "Call/ECC","0"

^SCFG: "Call/Speech/Codec","0"

^SCFG: "GPRS/AutoAttach","enabled"

^SCFG: "Gpio/mode/ASC1","std"

^SCFG: "Gpio/mode/DAI","gpio"

^SCFG: "Gpio/mode/DCD0","gpio"

^SCFG: "Gpio/mode/DSR0","gpio"

^SCFG: "Gpio/mode/DTR0","gpio"

^SCFG: "Gpio/mode/FSR","gpio"

^SCFG: "Gpio/mode/GPSANT","gpio"

^SCFG: "Gpio/mode/HSIC","rsv"

^SCFG: "Gpio/mode/PULSE","std"

^SCFG: "Gpio/mode/PWM","gpio"

^SCFG: "Gpio/mode/RING0","gpio"

^SCFG: "Gpio/mode/SPI","rsv"

^SCFG: "Gpio/mode/SYNC","gpio"

^SCFG: "Ident/Manufacturer","Cinterion"

^SCFG: "Ident/Product","EHS8"

^SCFG: "MEShutdown/Fso","0"

^SCFG: "MEShutdown/sVsup/threshold","0","0"

^SCFG: "MEopMode/CFUN","0","1"

^SCFG: "MEopMode/Comp1",""

^SCFG: "MEopMode/ExpectDTR","current"

^SCFG: "MEopMode/ExpectDTR","powerup"

^SCFG: "MEopMode/SoR","off"

^SCFG: "Radio/Band","511"

^SCFG: "Radio/Mtpl","0"

^SCFG: "Radio/OutputPowerReduction","4"

^SCFG: "Serial/Interface/Allocation","1","1"

^SCFG: "Serial/USB/DDD","0","0","0409","1E2D","0058","Cinterion Wireless Modules","EHx",""

^SCFG: "Tcp/IRT","3"

^SCFG: "Tcp/MR","10"

^SCFG: "Tcp/OT","6000"

^SCFG: "Tcp/WithURCs","on"

^SCFG: "Trace/Syslog/OTAP","0"

^SCFG: "URC/Ringline","local"

^SCFG: "URC/Ringline/ActiveTime","2"

^SCFG: "Userware/Autostart","1"

^SCFG: "Userware/Autostart/Delay","20"

^SCFG: "Userware/DebugInterface","0.0.0.0","0.0.0.0","0"

^SCFG: "Userware/DebugMode","off"

^SCFG: "Userware/Passwd",

^SCFG: "Userware/Stdout","usb4",,,,"off"

^SCFG: "Userware/Watchdog","1"

OK

Are there any configurations I’m missing?

Regards,

Kai Barkmann