Thales' cellular IoT products business is now part of Telit Cinterion, find out more.

You are here

Community > Forum > Global Discussion > Download on BGS5

Download on BGS5 | Telit Cinterion IoT Developer Community

Like
0
10
ericjanpot's picture
ericjanpot

May 2, 2016 - 8:40am, 6010 views

I am sucessfully downloading software (JAR/JAD) into the flash using AT^SJDL=1 commands. 

But, if am using `AT^SJAM=0,"a:/A9Sw/theSoftware.jad",""` after 20seconds a ^SYSLOADING is responding, in stead of OK. The software is installed and starting, but I was wondering if this normal?

10
Comment
Log in or register to post comments
Bartłomiej Gemalto Moderator's picture
Bartłomiej Gema...
May 2 2016 - 11:46am

Hello,

So you get "^SYSLOADING" while installing the application but the application is installed after that even though there's no OK reply and it is possible to run it then? Is it reproducible? Normally you should get OK reply or ERROR and ^SYSLOADING is only thrown on system start. And you should generally wait for SYSSTART before issuing commands to the module.

What interface are you using? You could redirect system out to ASC0 and check if there's anything unusual. Could you also paste AT^SCFG? output?

Regards,

Bartłomiej

ericjanpot's picture
ericjanpot
May 2 2016 - 12:14pm

I am using a Java class with import gnu.io.SerialPort; from the RXTX library 1.7

Here the response of AT^SCFG?

 AT^SCFG?
^SCFG: "Call/ECC","0"
^SCFG: "Gpio/****/ASC1","rsv"
^SCFG: "Gpio/****/DAI","gpio"
^SCFG: "Gpio/****/DCD0","gpio"
^SCFG: "Gpio/****/DSR0","std"
^SCFG: "Gpio/****/DTR0","std"
^SCFG: "Gpio/****/FSR","gpio"
^SCFG: "Gpio/****/PULSE","gpio"
^SCFG: "Gpio/****/PWM","gpio"
^SCFG: "Gpio/****/RING0","gpio"
^SCFG: "Gpio/****/SPI","std"
^SCFG: "Gpio/****/SYNC","gpio"
^SCFG: "GPRS/AutoAttach","enabled"
^SCFG: "Ident/Manufacturer","Cinterion"
^SCFG: "Ident/Product","BGS5"
^SCFG: "MEopMode/SoR","on"
^SCFG: "MEShutdown/Fso","0"
^SCFG: "Radio/OutputPowerReduction","4"
^SCFG: "Serial/Interface/Allocation","0","0"
^SCFG: "Serial/USB/DDD","0","0","0409","1E2D","0059","Cinterion Wireless Modules","Cinterion BGx USB Com Port",""
^SCFG: "Tcp/IRT","3"
^SCFG: "Tcp/MR","10"
^SCFG: "Tcp/OT","6000"
^SCFG: "Tcp/WithURCs","on"
^SCFG: "Trace/Syslog/Otap","0"
^SCFG: "Userware/Autostart","0"
^SCFG: "Userware/Autostart/Delay","50"
^SCFG: "Userware/Passwd",
^SCFG: "Userware/Stdout","null",,,,"off"
^SCFG: "Userware/Watchdog","0"
^SCFG: "Radio/Band","15"

OK
ericjanpot's picture
ericjanpot
May 2 2016 - 2:16pm

Yes , it's reproducible. I now noticed that stopping a midlet with (AT^SJAM=2) also results in ^SYSLOADING directly after W [2016-05-02T11:13:09Z] DestroyApp called is written to SYSTEM.OUT.

ericjanpot's picture
ericjanpot
May 3 2016 - 8:22am

Update, I narrowed down the "problem" a bit. 

Directly after the device starts (^SYSSTART) I enter following commands:
> AT^SCFG="Userware/Autostart","","0"
> AT^SCFG="Userware/Stdout","null",,,,"off"
> AT^SMSO
The device (BGS5/REVISION 01.100) restarts with a (SYSLOADING & SYSINFO), so no software is started. But, exactly 200 seconds after the SYSLOADING response the unit is rebooting with response below. This behaviour is repoducible and always 200 seconds, after the SYSLOADING. If in between commands are sends (such as AT^SJDL) this reboot still happens after 200 seconds. For this reason a larger JAR and following install command can not finish in this 200 seconds timeframe.  

^SYSLOADING

^SYSLOADING

^SYSINFO: 200

^SYSLOADING

^SYSLOADING

^SYSINFO: 200

Alopez's picture
Alopez
May 3 2016 - 9:48am

Hi Ericjanpot,

your module has disabled the loading of the JRC or just the JRC has been deleted of the FFS.

chekc with at^sjam=5 if the JRC is running.

the quickly way to solve the situation is to reflash the firmware in the module

Regards

ALopez

Somewhere over the rainbow!!! Looking for the Oz Land!!!

pfniyigena's picture
pfniyigena
Jun 16 2016 - 3:51pm

Hello Alopez,

How can I reflash the firmware when I can't access USB port for the module?

Bartłomiej Gemalto Moderator's picture
Bartłomiej Gema...
Jun 17 2016 - 2:00pm

You can do it on serial interface.

Bartłomiej Gemalto Moderator's picture
Bartłomiej Gema...
May 4 2016 - 11:47am

Hello,

The JRC is a factory MIDlet that implements some of the module's functionality and it starts automatically when the global autostart for applications is enabled. So you should not set AT^SCFG="Userware/Autostart","","0". When system starts it displays ^SYSLOADING and when JRC is started the ^SYSSTART is also displayed. The option "Userware/Autostart/Delay" also influences JRC. 

Regards,

Bartłomiej

ericjanpot's picture
ericjanpot
May 9 2016 - 11:06am

Thanks. Having JRC enabled seems to solve the problem.

I now have a smaller problem left, with downloading a 550kB JAR on the unit using AT^SJDL1. In ~30% of the cases the JDL **** does not return a checksum but a timeout. I am using the default 115200 baut rate ****. Can anybody give me a hint on this?

Bartłomiej Gemalto Moderator's picture
Bartłomiej Gema...
May 10 2016 - 2:55pm

Hello,

Can you write some more details? What terminal program is used? Which interface are you using: USB or UART? Is it always the same file with the same size? Is it possible that the file is used by another application at that time or there is not enough space in the module's file system?

Regards,

Bartłomiej