at^sjam does not give response | Telit Cinterion IoT Developer Community
October 25, 2016 - 4:09pm, 6148 views
Hello,
at^sjam=4 and at^sjam=0 commands does not give response for BGS5T. It does not work also after power off-on. at^sjam=5 works. It says only JRC is working.
I think a problem occured with FFS. Before problem occured, lastly, I was running an application via Eclipse, that is, online running as Emulator.
What can be the reason of problem? Did you experince same issue? What can I do to solve?
Best Regards,
Ergün.
Hello,
Is there neither ERROR nor OK reply? Is it possible to send any other command after that? Are you able to access FFS with MES?
Are there any MIDlets installed? Is it possible to run them? Please send the ATI1 and AT^SCFG? replies. I haven't heard about such problems so far.
Regards,
Bartłomiej
Hello Bartlomiej,
Neither ERROR nor OK reply. After error occurred, module does not reply also the other commands. Only the first character of my sent string comes back. I fI send AT+..'A' comes back. If I send "try" it responses 't'.("try" is an example string only. No matter what you wrote, the first character comes back.)
I can't access FFS via MES if I use same com port of that at command sent. If I change port setting of MES, I can get into and copy files.
I'm not sure any MIDlets installed in it. Since I can't use at^sjam=4, I can't see them. Probably last eclipse code exists in module. Eclipse loads jar,jad during online run.
ATI1 and SCFG? responses are below:
ati1
Cinterion
BGS5
REVISION 01.100
A-REVISION 00.000.10
OK
---------------------------------------
at^scfg?
^SCFG: "Call/ECC","0"
^SCFG: "GPRS/AutoAttach","enabled"
^SCFG: "Gpio/mode/ASC1","std"
^SCFG: "Gpio/mode/DAI","gpio"
^SCFG: "Gpio/mode/DCD0","std"
^SCFG: "Gpio/mode/DSR0","std"
^SCFG: "Gpio/mode/DTR0","std"
^SCFG: "Gpio/mode/FSR","gpio"
^SCFG: "Gpio/mode/PULSE","gpio"
^SCFG: "Gpio/mode/PWM","gpio"
^SCFG: "Gpio/mode/RING0","std"
^SCFG: "Gpio/mode/SPI","rsv"
^SCFG: "Gpio/mode/SYNC","std"
^SCFG: "Ident/Manufacturer","Cinterion"
^SCFG: "Ident/Product","BGS5"
^SCFG: "MEShutdown/Fso","0"
^SCFG: "MEopMode/SoR","on"
^SCFG: "Radio/Band","15"
^SCFG: "Radio/OutputPowerReduction","4"
^SCFG: "Serial/Interface/Allocation","1","1"
^SCFG: "Serial/USB/DDD","0","0","0409","1E2D","0059","Cinterion Wireless Modules","Cinterion BGx USB Com Port",""
^SCFG: "Tcp/IRT","3"
^SCFG: "Tcp/MR","10"
^SCFG: "Tcp/OT","6000"
^SCFG: "Tcp/WithURCs","on"
^SCFG: "Trace/Syslog/Otap","0"
^SCFG: "URC/Ringline","local"
^SCFG: "URC/Ringline/ActiveTime","2"
^SCFG: "Userware/Autostart","1"
^SCFG: "Userware/Autostart/Delay","0"
^SCFG: "Userware/Passwd",
^SCFG: "Userware/Stdout","usb1",,,,"off"
^SCFG: "Userware/Watchdog","0"
OK
Hello Bartlomiej,
I'm working on a Timer,TimerTask application.
The problem occurred when working that application with eclipse online run.
I have changed the BGS5T module, I'm working on that now.
There are some strange situations.
There were 2 same application installed on module. I deleted one of them with at^sjam=3 then at^sjam=4 response is below. My example seems to be in "u". What is it?
Thanks.
^SJAM: "u","TimerTest MIDlet Suite","MIDlet Suite Vendor","1.0.0",0
^SJAM: "a:/JRC-1.50.3.jad","Java Remote Control MIDlet Suite","Cinterion","1.50.3","1"
There writes onlu "u". Neither a directory nor a jad.
"u" part changes after power off-on. I had 2 different response so far.
AT^SJAM=4
^SJAM: "şÊ","TimerTest MIDlet Suite","MIDlet Suite Vendor","1.0.0",0
^SJAM: "a:/JRC-1.50.3.jad","Java Remote Control MIDlet Suite","Cinterion","1.50.3","1"
OK
AT^SJAM=4
^SJAM: "1","TimerTest MIDlet Suite","MIDlet Suite Vendor","1.0.0",0
^SJAM: "a:/JRC-1.50.3.jad","Java Remote Control MIDlet Suite","Cinterion","1.50.3","1"
OK
Hello,
This behaviour is very strange. In case of the second module I'd try to uninstall the 'u' application.
Please try to run gWinSwup with "Recovery file system" option and check if it has solved the problem.
Regards,
Bartłomiej
Hello Bartlomiej,
at^sjam=3,"u","" replies ERROR.
How to run gWinSwup? Can you give some detail?
Where can find it? Run from command prompt, windows cmd? Or is it an exe? In which directory..etc
I have sent you the gWinSwup. Please try.
Normally you can get it from the local distributor od dowload from extranet if you have accesss.
Regards,
Bartłomiej
Hello Bartlomiej,
Thank you very much.
I have updated firmware and JRC of 2 module using gWinSwup.exe.
at^sjam=4 works for previous module now.
I couldn't test my Timer/Timertask application yet. I will observe the results after running it via IMP Debug Connection.
Best Regards,
Hello,
I have the same problem.
AT^SJAM=4
^SJAM: "??","SMSSuite","company","1.0","1"
^SJAM: "??????????","SMSSuite","company","1.0","1"
^SJAM: "??","SMSSuite","company","1.0","1"
^SJAM: "a:/JRC-1.50.3.jad","Java Remote Control MIDlet Suite","Cinterion","1.50.3","1"
ATI1
Cinterion
BGS5
REVISION 01.100
A-REVISION 00.000.10
Could you send me gWinSwup for Gemalto BGS5T?
Pages