Usage status on SL Portal | Telit Cinterion IoT Developer Community
October 19, 2016 - 12:06pm, 2783 views
Hello, Everydays mornings I check how is going code's progress, but today could not check because I cannot get information on SL portal, no one information.
By console is displayed :
[INFO] Connection to platform established
also I can see
[INFO] [DataExchangeDeviceGRIPConnection: MyDataExchangeDevice4 id] refreshStringValue: index: 0 value: at^sctm?
^SCTM: 0,0,35
On SL no one refresh even using "get" from Data Exchange Unit device from portal.
No one information on Status also, only about connection
deviceProtocolVersion: 1
isConnected: true
maybe problem is in usage status , and if there is the problem how to fix it?
Hello,
Are the messages sent according to the log? Any error messages in the log? Do you have the whole log to check? If not please reboot the module, start the app again and check if there is anything unusual. Have you changed anything - in configuration, libraries used etc.?
Regards,
Bartłomiej
no one error message, I did not change anything from last time, all configuration and libraries was working normal.
this is the log:
nitializing Module Services
[INFO] [ModuleInformation] enable Board Temperature monitoring
[INFO] [ModuleInformation] enable FFS space monitoring
[INFO] [ModuleInformation] enable Supply Voltage monitoring
[INFO] [ModuleInformation] enable Sim Id monitoring
[INFO] [GSMEngine] Registering incoming SIM URCs
[INFO] Current imsi: 250990282284068
[INFO] [JammingUrcListener] Bind Atc interface
[INFO] [JammingUrcListener] Bind Atc interface: done
[INFO] =======================================================<
[INFO] [JammingUrcListener] Jamming detection active and ready
[INFO] =======================================================
SerialConnection: connected to USB3:115200
ATService: started without SLA Event No connection
Ready for the next command, insert 'VIN' to can acess to VIN configuration...
TESTING VALUE VIN:null
TESTING VALUE answer:String, no command, proving
TESTING VALUE answer2:null
TESTING VALUE excUnit4:proving String, no command
[INFO] [Bootstrap] Booting...
[INFO] SIM PIN was already entered before.
[INFO] [Bootstrap] Module registered to the network, and ready to connect!
[INFO] [Bootstrap] Connection parameters:;access_point=internet.beeline.ru;username=beeline;password=beeline;bearer_type=gprs
[INFO] [Bootstrap] Using ATPipeItelma3 as DEVICE ID
[INFO] GRIPExecutor: Connecting:
Address: 199.167.39.10:17198
Fall-back address: 199.167.39.10:17199
TLS: false
Gprs parameters: ;access_point=internet.beeline.ru;username=beeline;password=beeline;bearer_type=gprs
Keep-alive: 120 Idle timeout: 60 Power saving: false
[INFO] GRIPExecutor: onRegistryChange
[INFO] [DataExchangeDeviceStub: MyDataExchangeDevice4 id] call onReady
[INFO] [TaskProcessor] MessageTask_1(reattach_report(0,1072917836)) added
[INFO] [TaskProcessor] MessageTask_2(supply_voltage_report(4180,1072917836)) added
[INFO] [TaskProcessor] MessageTask_3(board_temperature(33,1072917837)) added
[INFO] [TaskProcessor] MessageTask_4(MyDataExchangeDevice5 id: measurement(MyDataExchangeUnit5(id: MyDataExchangeUnit5 id, label: command5, type: 7, readOnly: false))) added
[INFO] [TaskProcessor] MessageTask_5(MyVin id: measurement(MyVin(id: MyVin id, label: VIN, type: 7, readOnly: true))) added
[INFO] [TaskProcessor] MessageTask_6(MyDataExchangeDevice4 id: measurement(MyDataExchangeUnit4(id: MyDataExchangeUnit4 id, label: command2, type: 7, readOnly: false))) added
[INFO] [DataExchangeDeviceStub: MyDataExchangeDevice5 id] call onReady
[INFO] [DataExchangeDeviceStub: MyVin id] call onReady
[INFO] [Bootstrap] GRIP ready
[INFO] [Bootstrap] Successfuly connected to SL Portal in HIGH_AVAILABILITY mode<
[INFO] [GSMEngine] Registering incoming SMS URCs
[INFO] Connection to platform established
SLAEVENT: MESSAGE: Connection to platform established
[INFO] [SmsControl] Searching for platform messages to delete
[INFO] [NetworkAttachMonitor] Verifying CREG
[INFO] [NetworkAttachMonitor] New network attach detected
[INFO] [NetworkAttachMonitor] Attach rate: 1
[INFO] [NetworkAttachMonitor] Atttach attempts: 1
[INFO] [TaskProcessor] Start processing tasks
Hello,
On the moduel side it seems that everything is correct.
I've reported the problem. I hope it will be clarified soon.
Best regards,
Bartłomiej
Hello,
The problem is fixed now. Please test on your side.
Best regards,
Bartłomiej
Hello, yes, is working ! thanks.
But still continues the previous problem about answer. Still is not posible to can see the value, only Command I sent.
INFO] [DataExchangeDeviceGRIPConnection: MyDataExchangeDevice4 id] refreshStringValue: index: 0 value: at^sctm?SCTM: 0,0,35
Hello,
Please see the solution here:
https://iot-developer.thalesgroup.com/threads/how-obtain-answers-value-c...
Best regards,
Bartłomiej